FDS RAM adaptor cable pinout

From Nesdev wiki
Jump to: navigation, search

Diagram

Open-end view of the RAM adaptor's disk drive connector.

             ███████
 ████████████████████████████████
 ████████████████████████████████
 ███  1   3   5   7   9   11  ███
 ███                          ███
 ███  2   4   6   8   10  12  ███
 ████████████████████████████████
 ████████████████████████████████

Pin meanings

pin # *2C33 pin *RAM pins I/O signal description
1 50 5 (green) O /write
2 64 C (cyan) O VCC (+5VDC)
3 49 6 (blue) O /scan media
4 32 1 (brown) O VEE (ground)
5 52 3 (orange) O write data
6 37 B (pink) I motor on/battery good
7 47 8 (grey) I /writable media
8 - - I motor power†
9 51 4 (yellow) I read data
10 45 A (black) I /media set
11 46 9 (white) I /ready
12 48 7 (violet) O /stop motor
notes on symbols
----------------
I/O: input/output
/ : Indicates a signal which is active on a low (0) condition.
* :	These are corresponding pinouts for the 2C33 I/O chip, and the other  end  
of the RAM adaptor cable, which both are located inside the RAM adaptor.
† :	The RAM adaptor does not use this signal (there is no wire in the cable 
to carry the signal). An electronically controlled 5-volt power supply 
inside the disk drive unit generates the power that appears here. This power 
is also shared with the drive's internal electric motor. Therefore, the 
motor only comes on when there is voltage on this pin.

Signal Descriptions

Pin 1 (Output) /write

While active, this signal indicates that data appearing on the "write data" signal pin is to be written to the storage media.

Pin 3 (Output) /scan media

While inactive, this instructs the storage media pointer to be reset (and stay reset) at the beginning of the media. When active, the media pointer is to be advanced at a constant rate, and data progressively transferred to/from the media (via the media pointer).

Pin 5 (Output) write data

This is the serial data the RAM adaptor issues to be written to the storage media on the "/write" condition.

Pin 6 (Input) motor on, battery good

Applicable mostly to the FDS disk drive unit only, after the RAM adaptor issues a "/scan media" signal, it will check the status of this input to see if the disk drive motor has turned on. If this input is found to be inactive, the RAM adaptor interprets this as the disk drive's batteries having failed. Essentially, this signal's operation is identical to the above mentioned "motor power" signal, except that this is a TTL signal version of it.

Pin 7 (Input) /writable media

When active, this signal indicates to the RAM adaptor that the current media is not write protected.

Pin 9 (Input) read data

When "/scan media" is active, data that is progressively read off the storage media (via the media pointer) is expected to appear here.

Pin 10 (Input) /media set

When active, this signal indicates the presence of valid storage media.

Pin 11 (Input) /ready

Applicable mostly to the FDS disk drive unit only, the falling edge of this signal would indicate to the RAM adaptor that the disk drive has acknowledged the "/scan media" signal, and the disk drive head is currently at the beginning of the disk (most outer track). While this signal remains active, this indicates that the disk head is advancing across the disk's surface, and apropriate data can be transferred to/from the disk. This signal would then go inactive if the head advances to the end of the disk (most inner track), or the "/scan media" signal goes inactive.

Pin 12 (Output) /stop motor

Applicable mostly to the FDS disk drive unit only, the falling edge of this signal would instruct the drive to stop the current scan of the disk.